2N2219 TRANSISTOR DATASHEET PDF

2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N Silicon NPN Transistor. Data Sheet. Description. Semicoa Semiconductors offers: • Screening and processing per MIL-PRF Appendix E. DATA SHEET NPN switching transistor in a TO metal package. collector- emitter voltage open base. 2N −. V. 2NA. −.

Author: Nikogore Negal
Country: Qatar
Language: English (Spanish)
Genre: Relationship
Published (Last): 10 December 2004
Pages: 470
PDF File Size: 7.98 Mb
ePub File Size: 1.89 Mb
ISBN: 795-2-61163-710-9
Downloads: 71898
Price: Free* [*Free Regsitration Required]
Uploader: Maukora

2N Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on. But this calculation will lead to the closest value to start with. To make this current flow through the transistor the dafasheet of base current I B can be calculated using the below formula:.

TL — Programmable Reference Voltage. When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter.

So if you looking for an NPN transistor that could switch loads or transisstor decent amplification then 2N might the right choice for your project. Another important thing to keep in mind, while using a transistor as switch is the base resistor.

2N2219 Datasheet, Equivalent, Cross Reference Search

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. Datasneet Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1. So the value if R B will be.

  HIRAYAMA HVE 110 PDF

This resistor is connected to the base pin of the transistor to limit the current flowing through the base. Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula: Current Drains darasheet through emitter, normally connected to ground.

Here lets us assume the load here consumes around mA maximum so our collector current Dztasheet C mA.

In our case for a collector current of mA we have tdansistor pass a base current of 16mA. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

Where h FE, is the current gain of the transistor which in our case is But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle.

  CZARNY KSI KARYN MONK PDF

2N Datasheet(PDF) – NXP Semiconductors

However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.

So to calculate the resistor value of the base we can use the formulae. Amplifier modules like Audio amplifiers, signal Amplifier etc. The 2N is a NPN transistor and is normally used as a switch in many circuits. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin. Complete Technical Details can be found at the datasheet given at the end of this page.

The value of this current can be calculated by the required amount of current that will be consumed by the load. Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. Current flows in through collector, normally connected to load. Submitted by admin on 21 June This stage is called Saturation Region.