33220A MANUAL PDF

The A function generator and all associated options will be The Keysight Technologies A func- . Operating manual, service manual, quick. Service Guide. Publication Number (order as manual set) The Agilent Technologies A is a 20 MHz synthesized function. Buy Keysight Technologies A Function Generator 20MHz GPIB, LAN, USB A. Operating manual, service manual, quick reference guide, IntuiLink.

Author: Sharr Mozahn
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Technology
Published (Last): 13 September 2012
Pages: 386
PDF File Size: 18.46 Mb
ePub File Size: 7.77 Mb
ISBN: 823-1-58319-764-9
Downloads: 14806
Price: Free* [*Free Regsitration Required]
Uploader: Shakarisar

Note that since the rear-panel Modulation In connector is dc- coupled, you can use the A to emulate a voltage-controlled oscillator VCO.

manuap For example, the following command string guarantees that the first trigger is accepted and the operation is executed maual the second trigger is recognized. Chapter 4 Remote Interface Reference Simplified Programming Overview Simplified Programming Overview This section gives an overview of the basic techniques used to program the function generator over maual remote interface. The default is Sine.

Select from 1 cycle to 50, cycles, in 1 cycle increments see the restrictions below. Page Chapter 5 Error Messages Execution Errors Settings conflict; not able to sweep noise, sweep turned off The function generator cannot generate a sweep using the noise function. A fifth storage location automatically holds the power-down configuration of the instrument. Disable or enable the burst mode. The default is NORM true-high logic. The following steps show you how to change the amplitude to 50 mVrms.

Errors are cleared as you read them. Page Chapter 3 Features and Functions Calibration Overview To Unsecure for 33220aa You can unsecure the function generator either from the front panel or over the remote interface. Page triggered modeCD-ROM, connectivity software 15 status byte register waveform frequency CD-ROM, shipped with A blank display burst phase center frequency, sweep block format, binary degrees vs.

Select the source of the modulating signal. The factory setting is enabled ON. Calibration Overview This section gives a brief introduction to the calibration features of the function generator.

  AVERY 8869 TEMPLATE PDF

Make sure that you have selected the proper trigger source and verify kanual the sweep or burst mode is enabled.

AGILENT TECHNOLOGIES A USER MANUAL Pdf Download.

The Agilent A has a fixed series output impedance of 50 ohms to the front-panel Output connector. Each character must be a letter “a” IMMediate Clears all instrument memory except for the boot parameters and calibration constants.

Page Chapter 3 Features and Functions Calibration Overview To Change the Security Code To change the security code, you must first unsecure the function generator, and then enter a new code. This information is not directly related to waveform generation but is an important part of operating the function generator.

33220s

Page Chapter 5 Error Messages Execution Errors Data out of range; large period limits minimum pulse width For a pulse waveform, the minimum pulse width is 20 ns for periods up to 10 seconds. Page Command Separators A colon: Chapter 3 Features and Functions System-Related Operations Display Control For mznual reasons, or to speed up the rate at which the function generator can execute commands from the remote interface, you may want to turn off the front-panel display.

You can output the arbitrary waveform directly from volatile memory or you can copy the waveform to non-volatile memory using the DATA: Cross-isolation UART framing error This section describes the low-level commands used to program the function generator. However, waveforms of greater than 16, 16K points cannot be edited from the Agilent A front panel.

To change the security code, you must first unsecure the function generator using the old security code, and then enter a new code. This generic message indicates that the manuao edge time is limited to an upper or lower boundary which is dictated by the instrument hardware.

  FORM HUD 92544 PDF

The commands used for AM are listed on the next page. When enabled, a TTL-compatible square waveform with either a rising edge default or falling edge is output from the Trig Out connector at the beginning of the sweep.

When enabled using the OUTP: Nonvolatile arb waveform memory corruption detected The non-volatile memory used to store arbitrary waveforms has detected a checksum error. Calibration Security This feature allows you to enter a security code to prevent accidental or unauthorized calibrations of the function generator.

Agilent Technologies 33220A User Manual

In the triggered mode, the number of cycles specified by the burst count is output at the waveform frequency. Chapter 3 Features and Functions Calibration Overview To Unsecure for Calibration You can unsecure the function generator either from the front panel or over the remote interface. Press the IP Setup softkey. MIN selects the lowest frequency allowed for the selected function and MAX selects the highest frequency allowed.

The width of the mmanual can be expressed either as a pulse width expressed in time units, like the period or a duty cycle expressed as a percentage of the period.

In fact, any periodic signal can be represented as the sum of different sine waves. Creating Arbitrary Manua or interpolate as necessary to fill waveform memory.

33220A Function / Arbitrary Waveform Generator, 20 MHz

TIME command to set the number of seconds required to sweep from the start frequency to the stop frequency. UNIT command on page for more information. Chapter 3 Features and Functions Frequency Sweep Sweep Trigger Source In the sweep mode, the function generator outputs a single sweep when a trigger signal is received.