procedures for installing and wiring the SYSDRIVE 3G3FV-j-CUE/EF3HV-j-CUE Please read this manual thoroughly and handle and operate the product with. The SYSDRIVE 3G3FV is OMRON’s new special-purpose inverter. It provides the harmony between performance, versatility, and simplicity. Using a unique. Manuals and User Guides for Omron SYSDRIVE 3G3FV. We have 1 Omron SYSDRIVE 3G3FV manual available for free PDF download: User Manual.

Author: Vuran Maule
Country: Sri Lanka
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 25 March 2010
Pages: 123
PDF File Size: 19.95 Mb
ePub File Size: 1.48 Mb
ISBN: 826-3-88018-557-8
Downloads: 33592
Price: Free* [*Free Regsitration Required]
Uploader: Kazigrel

Measuring 3g3ff Step Response Waveform Use the following procedure to measure the step response waveform. Page Chapter 6 Advanced Operation Parameter Settings The following table shows the setting information for the multi-function outputs.

Omron SYSDRIVE 3G3FV User Manual

This is extremely hazardous. The operation mode display will appear. E Base frequency FA: 3g3tv voltage balance between phases is bad. Run Source And Responsiveness Settings Regenerating Restart enabled ON: When trim control increase and decrease are selected as multi-function contact input functions setting: New Functions, Software Ver.

Omron SYSDRIVE 3G3FV Manuals

Chapter 8 Maintenance Operations The Inverter is not in operation mode. Page Chapter 6 Advanced Operation The multi-function outputs can be set to monitor any of the U1 Inverter status items by setting the last two digits of the parameter number U1- Refer to page for a table listing all of these U1 settings.


If a load is connected when auto-tuning is performed, not only will incorrect motor parameters be re- corded, but the motor may operate erratically resulting in dangerous conditions such as loads falling from vertical axis motors. S Numeric input from the Digital Operator S Voltage input within a range from 0 to 10 V S Voltage input within a range from 0 to 10 V With minus voltage, rotation is in the opposite direc- tion of the run command. According to instructions in manual.

After the stop command is input and the minimum baseblock time L has elapsed, DC braking is applied and the motor stopped. Page Chapter 6 Advanced Operation Parameter o determines whether the elapsed operating time is the time that the Inverter is on or the time that the Inverter is running.

OMRON SYSDRIVE 3G3FV Series Inverters

STOP Interrupt the output. When supplying a voltage input to the frequency reference current input terminal 14be sure to disconnect jumper 3t3fv J1 on the control board.

Run commands are ignored during deceleration time. Make sure that these protective covers are on the product before use. The setting range for all of the values is 0 to the max. Select Language display Displays the Control Method display.

If the motor capacity is less than the Inverter capacity the maximum application motor capacityraise the set value. An access level is a range of parameters that can be set or referenced. Don’t have an account? Transportation Precautions Caution Do not hold by front cover or panelinstead, hold by the radiation fin heat sink while transporting the product.


This is the factory-set manua.

Motor Constant Parameter Lists If that should occur, use this section as a reference and apply the appropriate measures. DC braking is used to prevent the motor from rotating due to inertia or external forces when the Inverter is stopped.

Clear the recorded user defaults. Caution Be sure to confirm permissible ranges of motors and machines before operation because the Inverter speed can be easily changed from low to high. Speed Loop asr Structure Summary Of Common Control Functions Output voltage V Frequency Hz Note 1. Four acceleration times and four deceleration times can be set.

Chapter 8 Maintenance Operations high leakage detection level i. Page 22 Chapter 1 Introduction The 3G3FV allows the following three kinds of access levels to be set in order to further simplify pa- rameter setting. In control modes with PG, i. Chapter 4 Trial Operation Procedure 1. Chapter msnual Maintenance Operations A signal is being input to the frequency reference current terminal Double the values for V class Inverters.