8255 INTERFACING WITH 8086 PDF

Interfacing With Microprocessor A interface to microprocessor. Module 3: I/O programming: I/O addresses MAP of x86 PC’s, programming and . To have more pins for I/O, the is interfaced to – a PPI (Parallel. Microprocessor | (programmable peripheral interface) ยท Interface with Subtract content of two ports by interfacing with microprocessor first_page program to determine subtraction of corresponding elements of.

Author: Kajisar Shaktigor
Country: Lithuania
Language: English (Spanish)
Genre: Software
Published (Last): 26 December 2005
Pages: 263
PDF File Size: 14.99 Mb
ePub File Size: 13.38 Mb
ISBN: 693-4-60922-727-3
Downloads: 7011
Price: Free* [*Free Regsitration Required]
Uploader: Manris

To make this website work, we log user data and share it with processors. This can be solved in many ways. Thus a pulse can be generated at OUT at desired instant depending on preset count value. Is counter is in NULL state. Timers and Counters in Microcontroller.

In this section we discuss many useful applications like keyboard and display interface, traffic light control, printer interface and so on. The count for rotating the shaft of the stepper motor through a specified angle may be calculated from the no. Auth with social network: We think you have liked this presentation. Ports A, B, and C can be individually programmed as input or output ports Port C is divided into two 4-bit ports which are independent from each other Mode 1: The DAC find applications in areas like Digitally controlled gains Motor speed controls Programmable gain amplifiers etc.

  LIBRO DE RADIOLOGIA PEDROSA PDF

It employs rotation of its shaft in wihh of steps, rather than continuous rotation as in case of AC or DC motors. My presentations Profile Feedback Log out. Thus duration of pulse can be elongated. Used when programmer want to read the contents of any counter on the fly.

Feedback Privacy Policy Feedback.

8255A – Programmable Peripheral Interface

Intel has designed programmable peripheral interface PPI chip for this purpose. Ports are configured as input ports Input on reset CS – Used to select the chip. In one clock period of 10 KHz frequency there are clock periods of 10 MHz frequency.

Published by Derick Warren Modified over 3 years ago. Address lines A 0 โ€” A 1 are used by for internal decoding.

About project SlidePlayer Terms of Service. The port A address is h. An external feedback resister acts to control the gain. My presentations Profile Feedback Log out. Explain the mode of operation and initialisation. Second method is to read the content of counter using Read Back command. It has three 8-bit parallel ports: If you wtih to download it, please recommend it to your friends in any social system.

Published by Arleen Gray Modified over 2 years ago. To get absolute address, all remaining address lines A 15 โ€” A 2 are used to decode the address for Out of these 8 inputs only one can be selected for conversion by using 3 address lines A,B,C.

  FLUKE POWER LOGGER 1735 PDF

It generates a clock pulse interfzcing OUT at regular interval programmed through preset count value. The angle x may be calculated as: The format of status register is shown. Mode Interrupt on terminal count. The sequence of pulses can be decided, depending upon the required motion of the shaft. Interfacing of with The signal may be used to interrupt the CPU if required. Explain the mode of operation and initialization. Features of Programmable Interrupt Controller.

Interfacing with Microprocessor | Interfacing with

OUT is initially High. The Pulse width depends on the count value.

Minimum Mode Configuration of Your email address will not be published. Only lower data bus D 0 โ€” D 7 is used as is 8-bit device.

UNIT-IV 8255 PPI Various Modes Of Operation Interfacing To 8086.

Without disturbing the counting. Mode 5 – Hardware Triggered strobe. To make this website work, we log user data and share it with processors. Thus pulses are 886 continuously in mode 2 Mode 4 – When count reaches terminal count i.

UNIT-IV PPI Various Modes Of Operation Interfacing To ppt video online download

No continuous pulses are generated. The format of Read back command is. Interfacing with