AMERICAN AUDIO V1000 PDF

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Tojagal Shashura
Country: Gabon
Language: English (Spanish)
Genre: Education
Published (Last): 10 June 2006
Pages: 39
PDF File Size: 4.62 Mb
ePub File Size: 1.40 Mb
ISBN: 463-8-77960-301-6
Downloads: 54363
Price: Free* [*Free Regsitration Required]
Uploader: Kagagar

Um ddas Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. When dip switches 2 and amreican are in the “ON” the filter will cut off frequencies at and below 30Hz, when these dip switches are in the “OFF” position the filter will cut off frequencies at and below 50Hz.

VLP1000 power amplifier

Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector. Every Vplus series amplifier has been thoroughly tested V and has been shipped in perfect operating condition.

For cable runs shorter than 20ft. Banana Plugs – When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are completely screwed in.

During excessive clipping the limiter will reduce the audio signal enough to minimize the amount of clipping. Turn your input source level up. Cooling Fan – This breaker is designed to protect the amplifier and your speakers in the event of an AC overload. The appliance has been exposed to rain or water. Americwn proper polarity will avoid speakers being out of phase, that can cause a loss of bass response.

American Audio V1000 PLUS Manuals

Antes de usar este amplificador, lea mas advertencias en la guia de operacion. An ultrasonic network uncouples RF from the output and helps keep the amplifier stable with reactive loads. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

  LA CHICA DEL CRILLON PDF

If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes. The limiter has a fixed threshold and can not be adjusted.

The front panel provides four holes used to screw the unit into a rack. After inserting the wire into the binding post hole, screw the binding post cap down on the wire. Turn your equipment on your amplifier should always be the last item you turn on.

This fan is used to cool the internal parts of the amplifier when in use. Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.

V Power Amplifier by American Audio Valuation Report by

Channel 1 filters is control by dip switch 1 and channel 2 filter is controlled by dip switch 4. Cooling Fan Dual speed cooling fans.

Cooling Fan – Dual speed cooling fans. Connect your speakers to the outputs on the rear of the amplifier. Short Circuit Protection can usually be traced back to zudio signal output line i. Power Switch – This switch controls the units main power. Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping.

If the breaker continues to pop, stop using the amplifier and contact customer service. Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.

Be sure that your front gain g1000 are turned down to their lowest level full counter-clockwise.

  EVERMOTION VOL 113 PDF

No hay piezas adentro que el usario puede reparar. Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of overheating problems. The unit also provides a way to rear mount the unit into a rack for added security. See page 9 for more details on input configuration. When the input signal overloads, the “CLIP LED’s” indicate a signal overload, at this time, the master volume should be lowered to reduce distortion. Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable.

If the carton appears to be damaged, carefully inspect your unit for any damage and be sure all accessories necessary to operate the system have arrived intact. Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker connections will run between the two positive red leads.

During low level output the fans run at normal speeds. It’s a community-based project which helps to repair anything. Objects have fallen, or liquid has been spilled into the unit.

Always use the 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc. Insert the bare wire into the hole that was reveled by unscrewing the binding post cap.

American Audio V PLUS Manuals

The amplifier can operate at practically any power level without risk of overheating. Connect your inputs into channels one and two of the amplifier. Bridged-Mono Mode Caution – The voltage across the output terminals of a bridged Vplus series amplifier may equal or exceed Maerican volts RMS and may be as high as volts.