ASTM D6484 PDF

ASTM D is a test method used to study the compressive properties of a composite laminate that has a hole cut into it. The GD fixture meets the requirements of ASTM D for open-hole compressive strength testing of fiber-reinforced polymer-matrix composite. The ASTM D / DM fixture is used to perform open-hole compressive tests on multi-directional polymer matrix composite laminates reinforced with high .

Author: Voodoomi Doule
Country: Monaco
Language: English (Spanish)
Genre: Technology
Published (Last): 22 June 2014
Pages: 32
PDF File Size: 5.87 Mb
ePub File Size: 3.43 Mb
ISBN: 285-8-17087-877-1
Downloads: 23807
Price: Free* [*Free Regsitration Required]
Uploader: Vikinos

ASTM D Compression Fixture for Fiber Composite Laminates| GD

For non-ambient environmental conditions, the recommended? The ends of the grip-jaws on wedge-type grips should be even with each other following insertion to 11 avoid inducing a bending moment which could result in premature failure of the specimen.

Some types of damage, such as longitudinal splitting and delamination, can blunt the stress concentration caused by the hole, increasing the force-carrying capacity of the astmm and the calculated strength. NOTE 6—The hole diameter is ignored in the strength calculation; the gross cross-sectional area is used. A Standard 12″ Long by 1. This asrm design has been found to yield the highest likelihood of acceptable failure modes. End-loaded tests were performed with no additional?

Factors that influence the notched compressive strength and shall therefore be reported include the following: Precision and Bias The assembled fixture, with specimen installed, can be gripped at each end by hydraulic grips in the testing machine shear loadingor aligned vertically between f6484 platens end loading.

If the fixture is loaded between flat platens, some type of lateral constraint should be provided so that the fixture does not slip out from between the platens while being compression loaded, as a safety precaution. Guide plates are provided on each side of the fixture to maintain alignment of the assembly. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  BSNL TELEPHONE SURRENDER PDF

Anisotropic materials do not have a astj material coordinate system due to the total lack of symmetry, while, for isotropic materials, any ast, system is a principal material coordinate system.

Combining values from the two systems may result in nonconformance with the standard. Hydraulic wedge grips shall apply sufficient lateral pressure to prevent slippage between the grip face and the support? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. This device shall be essentially free from inertia lag at the speci? Flag symbol 1 For existing?

ASTM D6484 Testing Fixture

Tolerances may be applied to a nominal value to de? Estimate the coupon strength to aid in transducer selection, calibration of equipment, and determination of equipment settings.

However, cases such as elevated temperature testing of a moist specimen place unrealistic requirements on the capabilities of common testing machine environmental chambers.

Shear loading is preferred in the D64844 specification, but requires relatively large hydraulic grips, i.

ASTM D6484 Open-Hole Compression (OHC) Testing of CFRP

Subsequent Boeing specifications, and the ASTM standard, do not include these cutouts, strain gages not being used. A rectangle should be 4 FIG. The long and short? Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or adtm phonefaxor service astm.

  JEAN HANER YOUR HIDDEN SYMMETRY PDF

This standard is subject to revision at adtm time by the responsible technical committee and must be reviewed every? Sampling and Test Specimens 8. Damage caused by hole preparation will affect strength results.

In Procedure A, the? A number in parentheses indicates the year of last reapproval. Threaded support plate used with bolt-only installation. Tighten the four bolts just enough to hold the specimen in place during?

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Standard test specimens are 36 by mm [1. Adtm panel must be? The range of acceptable test laminates and thicknesses are described in 8. Terminology E 6 de? Threeplace failure mode descriptors, summarized in Table 1, shall be used.

ASTM D Open-Hole Compressive Strength of Polymer Matrix Composite Laminates_图文_百度文库

In the event of a con? Retests shall be performed for any specimen on which values are not calculated. The Boeing Open-Hole Compression test specimen is shear- or end-loaded in compression to failure in the fixture shown in Figs.

The threading of the support plate is optional. Historical Version s – view previous versions of standard. Work Item s – proposed revisions of this standard. The composite material forms are atm to continuous-fiber or discontinuous-fiber tape or fabric, or both reinforced composites in which the laminate is balanced and symmetric with respect to the test direction.

The force is transmitted by shear into the support?