Rosslare AYC-W Biometric Convertible PIN & Prox Reader/Controller. The sleek and compact design of Rosslare’s new Convertible dual-application. The AYC-W is an integrated reader and controller, designed for use either as a stand-alone unit or in conjunction with Rosslare’s BioTrax software system. : ROSSLARE AYC-W 26bit biometric w/prox reader: Biometric Security Devices: Camera & Photo.
|Published (Last):||2 July 2016|
|PDF File Size:||3.61 Mb|
|ePub File Size:||1.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
Controller Application Wiring Diagram 3 The wiring diagram 4 below shows the wiring for the reader application. Repeat the process from the beginning. In most circumstances, the unit should be located at approximately shoulder height.
AYC-W Biometric Convertible PIN & Prox Reader/Controller | Rosslare Security Products
Page 38 Controller Functionality Note: It has a reading range of up to 12 cm with an active card and up to 3 cm with a passive card. US Edition International Edition. Two short beeps one second apart are generated on power-on reset. The auxiliary input is connected to the door sensor output. Follow the steps below to select the appropriate Proximity Card reader transmission format you wish to use.
Fit for all access control applications from residential and commercial, to large-scale applications, our convertible product line is the answer to a wide variety of installations. Page 47 The auxiliary input is connected to the alarm system. When connected to a Rosslare intelligent Secure Power Supply, it converts into a user access controller.
EX control for the sec ond door. The auxiliary output is connected in parallel with the alarm’s door sensor output.
The card transmission format is set in Menu 2. Sign up now to:. It is inserted in the MSB byte of the transmitted data, one bit following the leading parity bit. Rosslare’s convertible product family – all the benefits of two-in-one Product Profile. This is indicated rosalare two short beeps on power-on reset.
Programming The Ayc-w Repeat the process from the beginning.
The door is opened by a valid code but there is no REX con trol for the second door. The auxiliary output is connected to the alarm. The auxiliary input is conne cted t o the door sensor output. Wiring Instructions If the tamper output is used, connect the purple wire to the correct input on the controller when rosspare as reader, or to the zone input of an intruder alarm system when used rosskare a controller.
Page 31 Activate the tamper sensor by removing the reader from the wall or removing the reader’s case.
Rosslare’s convertible product family – all the benefits of two-in-one
Or, 8 Wiegand 6 bit frames, 8 keys entered, followed by key. The auxiliary output is connected to the alarm system. Operating Temperature o C: General Information When the AYC-W unit is connected to a standard access controller, then it functions as a reader. To Res et the Programming Code Enter code according to the following: Enabling and Disabling Fingerprint Enrollment By default, when a user presents her proximity card or enters her PIN code for the first time, the AYC-W will eosslare request and enroll that user’s fingerprint.
Rosslare recommends that you maintain a written record of added and deleted users. To Set the Keypad Lockout Preferences: Page of 66 Zyc-w6500.
ROSSLARE AYC-W INSTALLATION AND OPERATION MANUAL Pdf Download.
This configuration is best for shielding the unit cable from external interference AYC-W Figure 2: In this mode, the auxiliary open code testcode2 and “Open A uxiliary” status users do not activate the ay-w6500 output. The au xiliary ou tput is connected to the lock on the second door.
When connected to a Rosslare auc-w6500 Secure Power Supply, it converts into a user fully featured secure access controller. The keypad transmission format is set in Menu 1. Rosslare Security announces release of ExClouds 2.
Make sure that the Reader status LED is red before proceeding. Multiple keys, Wiegand 26 bits, Single key, 6 bits, Rosslare format, Single key, 6 and 8 bits Wiegand. Activate the tamper sensor by removing the reader from the wall or removing the reader’s case.
It is not possible to program the unit while it is operating in Secure mode. The auxiliary output is connected to the lock on the second door.