BALTUR COMIST 72 PDF

COMIST 72) to run fan and a electric .. COMIST 72 N HEAVY OIL BURNERS SECTION .. Baltur reserves the right to change them without previous notice. baltur® Oil Burners are available as Gas, Light Oil, Heavy Oil and Dual Fuel. Industrial Units Available . COMIST 72 DSPGM. – COMIST DSPGM. 1) Noise levels measured in the Baltur laboratories by means of microphone positioned 1 metre behind the burner running on test boiler, at COMIST 72 N.

Author: Ducage Grogami
Country: Ethiopia
Language: English (Spanish)
Genre: Literature
Published (Last): 5 May 2013
Pages: 54
PDF File Size: 11.62 Mb
ePub File Size: 3.7 Mb
ISBN: 142-2-52628-127-6
Downloads: 97227
Price: Free* [*Free Regsitration Required]
Uploader: Kagajar

If the boiler thermostat or baaltur switch of the 2nd stage allows it regulated at a temperature or pressure value superior to that existing comixt the boilerthe servomotor which regulates the fuel delivery starts turning and determines a gradual increase in the fuel delivery and in the relative combustion air until it reaches the maximum delivery value at which the burner has been regulated. About us Leader in Italy and in Europe.

Maximum delivery is obtained when the return pressure is about 2 3 bar less that the delivery pressure normally comits. They should also be collected and disposed on in suitably prepared places so that they do no pollute the environment. The duration time of the pre-ventilation and oil precirculation phase is 22,5 seconds.

GI DSPN GI DSPN GI DSPN – PDF

Level 2 Spanish, 9 0 4 ckmist 6 L P 2 Level 2 Spanish, Listen to and understand spoken language in Spanish in less familiar contexts Credits: Fuel and combustion air delivery both increase at the same time until they reach maximum value fuel pressure at the return pressure regulator is equal to about bar if the pressure at the pump is at the value of bar. The atomized fuel which comes out of the nozzle is mixed with air supplied by the fan and is then ignited by the spark of the electrodes.

Before carrying out any cleaning or maintenance, switch off the equipment at the mains supply, using the system s switch or comis systems.

Schindler Planning naltur of high-rise elevators. Special warning notes Check that the person who carried out the installation of the burner fixed it securely to the heat generator so that the flame is generated inside the combustion chamber of the generator itself. Saveh Baptur City Category: Check that the air regulation device on the combustion head is in the position considered necessary for the fuel delivery required the air passage between the disk and the head should be considerably closed when the fuel delivery is relatively reduced; on the other hand, when the nozzle has a fairly high delivery, the air passage between the disk naltur the head should be relatively open see Chapter Regulation of the Combustion Head.

  KONE MONOSPACE 700 PDF

Subsequently, control combustion with the appropriate instruments and modify, if necessary, the previous regulation carried out by visual control only. Flues connected to high efficiency boilers and similar must therefore be of a size section and baptur insulation for the specific use to avoid such problems as those described above.

This provides flexibility, while allowing multiple devices to be use without the. You and Schindler share the same objective: For details, refer to the balrur electric diagram for each single burner. If it is decided not to use the burner any more, the following actions must be performed by qualified technicians: The shut down causes the immediate interception of the fuel and therefore the arrest of comkst burner and the red warning light comes on.

MNM modulating version, or on the command of the thermostat or pressure switch of the 2nd stage, if the burner is a GI DSPN two stage progressive version. Oil from the pump reaches the pre-heater, is heated to the correct temperature and when it comes out it passes through a filter before reaching the atomizer unit.

TEPSKART COMIST N

Nour commercial complex Category: I wash my hands, I wash my hair, I wash my face. Wait until fuel comes out haltur the hole, without air bubbles, and then re-close the gate valve.

We light your world From outline to skyline.

Some students have difficulty memorizing these facts, even though they are doing. It is advisable to regulate in such a way as to achieve a throttling of the air between the disk and the head; this will necessitate a considerable opening of the air shutter which regulates the flow to the burner s fan suction.

The value of the ignition flow rate minimum delivery should be about bar. Equipping for automatic fuel switching. In this way, modulation is activated exclusively by the automatic command of the boiler s probe, if the burner a GI High velocity and air turbulence ensure better penetration in the fuel and are therefore an optimum mixture and allow the burner to operate with good flame stability.

  HONEYWELL FG-1625 PDF

When we installed The LedEdit Software, on the desktop we can see following icon: Control box specifications Pre-ignition Time in seconds The air pressure switch must be set when the burner is started up and must be in function with the pressure value verified during operation with the ignition flame.

Serie COMIST N

If the cable gets damaged, switch off the equipment, and call only on qualified technicians for its replacement. Test yourself on just these flashcards at first. The minimum thermostat of the pre-heater closes when the temperature reaches the value at which it has been set. Operation is subject to the following two conditions: The works on the burner and on the esystem have to be carried out balur by competent people.

It should be kept in mind that the fuel should arrive at the nozzle with a viscosity rate not exceeding 2 E.

Flashcards Series 3 El Aeropuerto Flashcards Series 3 El Aeropuerto Flashcards are one of the quickest and easiest ways to test yourself on Spanish vocabulary, no matter where you are! Consequently, the pump pressure is taken to the normal value of about bar.

Technical and functional features. To ensure the efficiency and correct working of the equipment, it is essential to have periodic maintenance carried out by qualified technicians following the manufacturer s instructions. Fuel and combustion air delivery remain at maximum value until the boiler temperature pressure, if steam boilerapproaches the value at which it has been set and causes the modulation control motor to reverse its previous sense of movement.

If in doubt, call for a careful electrical check by a qualified technicians, since the manufacturer will not be liable for any damage caused by a poor ground connection. When maximum delivery desired has been reached, proceed with correcting the position of the combustion head; move it backwards and forwards in such a way as to obtain an air flow suitable for the fuel delivery with the air regulation in suction considerably open.

Make sure that the electric line to which the unit will be connected has frequency and voltage ratings suitable for the burner.