The tremolo has become one of b.y.o.c.’s most popular kits through word of mouth. And with good difficulty of the build is low. Welcome to /r/DIYPedals! This is an open community for the do-it-yourself pedal builders of reddit! Please use this subreddit to share. Shop new and used tremolo and vibrato pedals on Reverb. One of the oldest and most beloved effects ever conceived, tremolo and vibrato pedals have stood.

Author: Yomuro Shagis
Country: Equatorial Guinea
Language: English (Spanish)
Genre: Sex
Published (Last): 16 October 2018
Pages: 267
PDF File Size: 18.33 Mb
ePub File Size: 7.38 Mb
ISBN: 542-6-29764-194-1
Downloads: 80103
Price: Free* [*Free Regsitration Required]
Uploader: JoJokus

On the byoc site the jumper wires on the switch are connected differently.

Will have a thougher look tomorrow, anyone else having a go at this? I’m not sure if I can connect Sw7 directly to ground. It’s also a lot easier to build. Claudio 27 June at Only “complaint” is that the LED is a bit dimmer than is typical for pedals.

Thanks for verifying Paulo. So, I tried a transistor swap and used 2n Peavey hp exp, Squier 51 gfs liverpool in bridge Brass bottom in neckSquier jazzmaster Amps: Ron Nord 5 May at It’s a good sounding trem.

Tbh I don’t know the ins and outs byox the design, but Js and 2Ns are generally interchangeable with minor tonal changes at least in mu amp circuits etc. Gavin J Horsburgh 28 March byco I’d go BYOC just on a coolness factor.


Diode is 1n and connected differently also. Cool surf tones DVM! The diode is fine, I just connected in series instead of parallel so you don’t have to worry about it exploding as I do with most of these circuitsbut the R will obviously make a huge difference so great spot on that one.

Thanks to all for the effort. Can someone direct me pls.

byoc tremolo?

The time now is Paulo Rosa 29 October at This is true for the sound and the LED. Skajaquada 26 July at Skajaquada 6 December at Could this be modified? I was going to comment about the trim pot inside. So a big thank you to you as well! If I set it outside of the range, and then set it back it lags for seconds befor the effect kicks back in. If ground isn’t 0V then there is something wrong with the grounding of the effect. I’m almost finished with this build and I’ve run into a strange problem.

Unfortunately there are an awful lot of fake JFETs on ebay, so you are not alone in having problems with them! As to finish, it’s weird. Anybody have any ideas about what I should check? Thanks again for this great site! I put in a k C tremopo a reverse log and it acted like a k A. Login tremoko Sign Up.

BYOC Tremolo

Gonna try the rate mod mentioned above. It could be an issue whereby the specific gain of the transistors in this circuit is important, and your 2N were nearer to the required figure than your 2N And cool looking and sounding pedal! I would like to see where i can donate to for the site? Anyway, I did it, it sounds great, and my first attempt at etching the enclosure went really well.


I’m keen to build one that works well. Recorded with my “surf green” what else??

I made a byoc trem. When I engage it, the light pulses in time with the rate, but not getting any sound at tdemolo. I think I may just have everything for this build except the Ck Would love to give it a go when I get some time.

Which tremolo pedal finishing design do you prefer? Servant07 3 October at The BYOC trem sounds like an old amp’s trem to me.

BYOC Tremolo – Jorge Harada

Thank you Mark for the layout! Join the HC Newsletter. Have you wired up the switch, and if so is it working ok in bypass? Also you have 6.

Scott 13 June at Maybe can I change a resistor?