Fluke — A — Service and User Manual Revision: Manual-ID/Number: Date: 01 2 OPERATING INSTRUCTIONS Fluke Handheld True RMS Multimeter Calibration Manual, PDF, K. Fluke Fluke A Digital Multimeter Instructrion Manual, PDF, M. Digging through my old junk I found an old Fluke A meter. old test leads I need to dig up but does anybody have a manual for this thing?.
|Published (Last):||6 November 2014|
|PDF File Size:||2.86 Mb|
|ePub File Size:||14.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
Remove all plastic, vinyl and styrafoam products from the work area. Select a valid country. Adjust R28 for a dc voltmeter reading of 0.
Have one to sell? Filter will be reduced by the value of the feed-back voltage stored in Cl 8. Pennsylvania Replaced by Westinghouse Electric Corp. Your name or manul address: The following procedure pro- vides for open loop operation of the supplies to aid in localizing the defective supply.
Repairing a Fluke 8810A Multimeter
The following procedure is used to adjust the accuracy of each of the ac voltage ranges. Contact 8810q seller – opens in a new window or tab and request a shipping method to your location.
Read more about the condition. Maunal kfl is not available, prepare and install the Lockout Assembly as shown in Figure Autorange AUTO is included. Learn More – opens in a new window or tab Any international shipping is paid in part to Pitney Bowes Inc.
The resistance is 10 7 O on the V and V ranges. The Static Sensitive S.
Repairing a Fluke A Multimeter | All About Circuits
Skip to main content. Pennsylvania Use Skottie Electronics Inc. Troubleshooting information for each functional area is presented in the following paragraphs. Remove the input resistor.
San Jose, California, United States. Yes, my password is: When a range overload occurs full scale count of is exceeded the display will flash as an overload indication.
Fluke A Digital multimeter Manufacturer Fluke. Carlisle, Pennsylvania Electro-Midland Corp. The DOU provides a single-bit output indica- tion of a display overload condition.
Fuquay-Varian, North Carolina Penacook. For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fluie.
See all condition definitions – opens in a new window or tab This allows the input to U3 to be changed from the dc voltage representing the unknowm input to the appropriate reference input without affect- ing the charge stored 881a C9. Similar sponsored items Feedback on our suggestions – Similar sponsored items. Sell now – Have one to sell?
Stop electronic waste – fix it yourself
Second, the display will not indicate any applied dc input; producing a displayed readout of plus two or three digits of noise. Re-install the instrument in the case and re- place the case retaining manial. Select the kfl range. Adjust the 1 kO cal R13 for an A dis- play of 1.
Fluke A Digital multimeter Service and User Manual
The A employs a system of shields and guards that function, when properly connected, to minimize common mode to normal mode signal conversion.
Apply a kfl standard resistance to the input. Connect the oscilloscope input to TP The gain of the amplifier is determined by the ratio of the feed-back resistance, as selected flule range relay K6, K7, and K.
It consists of a series of subsections that include; introduction, accessories, and options. Compton, California Transistron Electronic Corp. If Free Run is allowed to go high, the DOU will automatically update the data after each measurement. Increase the divider output in I mV steps until the 88 1 0 A autoranges. The Ohms Converter California Weston Instruments Inc.
Time period B may indicate that the reference is low by not going to -1 volt. The following procedure is used to gain access mnual the interior of the A: Illinois Bunker Ramo Corp. Geneva, New York Ohmite Mfg. Autorange can also be manually selected as a range. Connect a shorting jumper across R34 and R Use the four-terminal measurement technique for this procedure.
Geneva, Illinois Birnback Radio Co. If the voltage does not meet this specification, then the trouble is contained within the regulator, Q22, Q23 and their associated components, or Q8, Q6, and Q4 Measure the voltage drop across R29 The inverter should supply enough current to develop