ARMY TM &P* AIR FORCE TO 11W TECHNICAL M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT M68 Cco Tm Manual Army – p s – scribd TM. CHAPTER I. PRESENTATION. Aimpoint CompM4 Reflex Sight is a rugged precision red dot Sight developed mainly for military and law enforcement. M68 SIGHT, REFLEX, W/QUICK RELEASE MOUNT AND SIGHT MOUNT CLOSE COMBAT OPTIC (CCO) (NSN ) (NSN ).
|Published (Last):||10 February 2018|
|PDF File Size:||13.71 Mb|
|ePub File Size:||11.45 Mb|
|Price:||Free* [*Free Regsitration Required]|
Right here, if ttm is the first time you are using this TM. Column 6 Qty Rqr. Column 3 lists the functions to be performed tn the item listed in column 2. If missing or damaged, replace ARD. Maintenance codes tell you the level s of maintenance authorized to use and repair support items. Open front lens cover 1. Please send an SF to the address listed in WP 00, pageReporting Equipment Improvement Recommendations EIRsto begin the warranty replacement action and note serial number and warranty expiration date.
Insert spare battery 2 into the double battery holder 3. Mount the Screw 4 to the C-Clamp. The NSN of the tool or test equipment.
For example, to learn about operating the sight, you would look in the Table of Contents and discover that Chapter 2 provides all pertinent information about the operation of the sight.
Make sure grabber edges are around mounting rail 2 and torque bar is in slot. Column 4 specifies each level of maintenance authorized to perform each function listed in column 3by indicating work time required expressed as manhours in whole hours or decimals in the appropriate subcolumn.
To make light adjustments, turn switch knob 1 clockwise. To ensure that sight assembly 1 is secure, tighten torque knob 3 until it snaps two times. Ensure that the prongs on the clip do not extend over the top of the foam pad.
M68 CCO should be ym on rail where the best field of view is achieved. When unserviceable, condemn and dispose of the Zitem at the level of maintenance shown in the third position of the SMR code. Name or identification of the tool or test equipment.
AA battery powered; up to 80, hours of use on a single good quality battery. Column 2 contains the item names of components, assemblies, subassemblies, and modules for which maintenance is authorized.
This column contains a brief description of the procedure by which the check is to be performed. The manufacturer’s part number. The five chapters, and what they contain, are found in the Table of Contents in the front of this manual. Look in the repair parts list work packages for the figure and item numbers.
Base assembly damaged in such a way that sight cannot be installed.
Inspect O-ring in battery cap. Remove Sight cfo weapon. Certain states identify lithium-manganese dioxide batteries as hazardous waste; these states are Alaska, California, Minnesota, Rhode Island, and Washington at present. They are authorized to the level indicated by the code entered in the third position of the SMR code. When applicable, this column contains a letter code, in alphabetical order, which is keyed to the remarks table entries.
Report all discrepancies in accordance with applicable service instructions e. When stacked they are approximately the same size and voltage. Both afloat and ashore intermediate levels are capable of complete repair of item. Using tools to tighten adjustments caps will damage threads.
The M68 Close Combat Optic
Install quick release plate 3. The front and rear lens covers should always be kept closed when the sight is not in use.
WP 00, page ; Comp M4: It is important that any corrosion problems with this item be reported so that the problem can be corrected and improvements can be made to prevent the problem in future items. The maintenance code entered in the fourth position tells you whether or not the item is to be repaired and identifies the lowest maintenance level with the capability to do complete repair perform m688 authorized repair functions.
Install sight mount 1 on M16A2 rifle handle using O-ring 2mounting bolt 3and CClamp 5 with bolt 4.
The last position is the extra high intensity setting. Ensure torque limiting assembly and rail grabbing clamping edge works.
The M68 Close Combat Optic |
When all visible particles of dust and dirt have been t, moisten a piece of lens paper, then gently wipe over the lens surfaces. Look up the item on the figure in the applicable repair parts list work package.
WPpage However, once this is accomplished, your field of view will increase and your target acquisition time will decrease.